NO LONGER AVAILABLE
Dry-Fluid Extreme Super Lubricant
HIGH END SLIDE-LUBRICANT FOR LINKS, SHAFTS AND BEARINGS
BALSAM FOR RC CARS
DryFluid Extreme was specially developed for radio controlled model cars with the aim to preserve as long as possible or rather to extend significantly the efficiency and lifetime of these mechanical marvels.
The effect of this new lubricant for links, shafts and bearings begins where others show their limits. Lowest sliding friction, maximum speed and minimal dust and dirt binding were the main objectives of the development. Findings in the aviation and vehicle industries and the expert knowledge of RC car pilots are the driving forces behind this new lubricant.
SLIDE-LUBRICANT INSTEAD OF OIL
DryFLuid is a dry slide-lubricant rather than a classic oil or grease. DryFluid is not wax, it is neither greasy nor oily but is silicone-free. A long-lasting lubrication effect is achieved using dry particles, sliding polymers and high end sliding fluids. The application and long-term effects of DryFluid Extreme will inspire every RC pilot.
PRODUCT-FEATURES
Reduction of power loss on links, shafts and bearings and it guarantees a long life of the treated components.
Lowest sliding friction for free movement and wear reduction
Multistage lubricant system with immediate and long-term effects
Dust and dirt repellent
Extremely good creeping abilities
Excellent material compatibility with all current metal, plastic and natural rubber materials Outstanding adhesive and anti-corrosive properties
This is classed as a hazardous material by our shippers and consequently cannot be sent outside the UK by air transport.
Within the UK it can only be sent by UPS not post. Please only select UPS for the shipping method at the checkout.
Authorised specialist dealer, Established 1987.
Dispatch normally within 24-48hrs DPD/ROYAL MAIL (Subject to Stock).
Sometimes if the countersunk m3 bolt is overtightened it can cause
the plastic to split.
This will not happen with this Optional part.
The SKYRC engine heater uses technology similar to that used by Formula 1, Indy Car and
NASCAR Teams! It will properly pre-heat your engine to 60-70°C in 10 minutes
based on ambient temperature.
SKYRC engine heater will pre-heat all the critical parts of your nitro engine, giving you a
minimal of stress and wear on the engine. It help relieve the stress on the crank,
con-rod, piston and sleeve during warm-up. It also give you a very easy and smooth
engine start, with no stress on your starterbox. Fuel consumption is much less, as
you do not have to spend time warming up and adjusting your engine. A pre-heatet
glow-plug will increase the life of your plug. It is also perfect for break-in, as it
reduces the "pinch" on your new engine. You will experience that engine pre-heating
is a must. Most importantly, it will quickly pay for itself by increasing engine life and
performance!
Features:
MCU control heating time and heating power for maximum safety.
Safety timer: turn off power around 10 minutes automatically.
Built-in temperature sensor: to control the output power of the heater.
LED indicator for status of engine heater.
12V DC source with low voltage cutoff.
Fireproof and heat resistant adjustable cover.
Fits all .19-.26 RC nitro engines.
Very small, lightweight and compact for quick and easy storage.
It's designed to transfer heat effectively and efficiently.
Access port on top allows you to start and monitor your engines temperatures
without having to take the heater off.
NEW SPECIAL LOW PRICE.
Compatible Response Mode with SUR, SSR, SHR, NOR SSL CODE5/CODE10
Function Quick Setup Wizard Fully Adjustable Trigger Adjustable Steering and Throttle Tension INDICATOR FUNCTION can show Receiver Signal Strength and Packet Delivery Ratio Weight: 382 g
Power source: AAA Battery x 3 ONLY Compatible RF with FH5 Includes new RX-493i receiver
One of the outstanding features of MT-5 is the indicator function which can check signal receiving conditions using RX-493i. The conditions can be used for checking the device and correct receiver placement.