LOW FRICTION PULLEY SET: MRX6 & 6R/X

B0514 (MUGEN)

CLUTCH SPRING ADJUSTING TOOL FOR 1/8 & 1/10 ON ROAD.

MUGEN STARTER BOX ( OFF ROAD ONLY)

Regarded by many drivers world-wide as the best Starter Box on the market.

Supplied in kit-form, it comes complete less batteries. Using either 2 x 2cell (7.4v Lipo or 6.6v Life) the starter offers real high torque with 2 motors and long life rubber drive wheel.

On-Road NOT available at present.

SSL Compatible
- Compatible with CODE10 (M12S (RS), Exzes ZZ, MT-44)
Not compatible with CODE5 (M12, Exzes Z, MT-4S, MT-4, MT-S)
- MULTI SETTING GEAR compatible
Not compatible with PGS SETTING GEAR
- SSR mode compatible
- SHR mode compatible
- Lipo 2 cell battery compatible
- High torque type
- Coreless motor
- Metal Gears
- AL Heat Sink

Programmable Servo to be compatible with SSL & Telemetry
- Setting Adjustment by wireless from Radio
- Setting Adjustment to connect Servo with Multi Setting Gear
- Regarding Temperature, Current, Voltage and Volume Position on Servo inside,
Telemetry-transmission can be passed to Radio.
# Initial Setting on Multi Setting Gear is necessary.

- Setting Items
- SSL-CH (SSL Channel Setting) - STRETC (Stretcher Adjustment) - BOOST (BOOST Adjustment)
- D-Band (Dead Band Adjustment) - MV-MID (Middle Torque Adjustment)
- MV-END (Later Torque Adjustment) - BREAK (Break Adjustment)
?MV-HOLD (Power Adjustment at whole area) ?MV-FRQ (Feeling Adjustment at whole area)
?MAX-PW (MAX Duty Adjustment)
- Multi Setting Gear is necessary for setting.

Speed
0.11 sec / 60° (7.4 V)
0.13 sec / 60° (6.0 V)

Torque
26.5 kg ·cm (7.4 V)
23.3 kg ·cm (6.0 V)

Dimensions
40.5 X 20.5 X 37.2 mm

Weight
59 g

FRONT BELT MRX6 +R/X RUBBER

Replaces plastic servo saver top Part No: H2325A.

Sometimes if the countersunk m3 bolt is overtightened it can cause
the plastic to split. 
This will not happen with this Optional part.

To fit MRX6R and MRXRX only.

The SKYRC engine heater uses technology similar to that used by Formula 1, Indy Car and 
NASCAR Teams! It will properly pre-heat your engine to 60-70°C in 10 minutes 
based on ambient temperature. 

SKYRC engine heater will pre-heat all the critical parts of your nitro engine, giving you a 
minimal of stress and wear on the engine. It help relieve the stress on the crank, 
con-rod, piston and sleeve during warm-up. It also give you a very easy and smooth 
engine start, with no stress on your starterbox. Fuel consumption is much less, as 
you do not have to spend time warming up and adjusting your engine. A pre-heatet 
glow-plug will increase the life of your plug. It is also perfect for break-in, as it 
reduces the "pinch" on your new engine. You will experience that engine pre-heating 
is a must. Most importantly, it will quickly pay for itself by increasing engine life and 
performance! 

Features:

MCU control heating time and heating power for maximum safety. 
Safety timer: turn off power around 10 minutes automatically. 
Built-in temperature sensor: to control the output power of the heater. 
LED indicator for status of engine heater. 
12V DC source with low voltage cutoff. 
Fireproof and heat resistant adjustable cover. 
Fits all .19-.26 RC nitro engines. 
Very small, lightweight and compact for quick and easy storage. 
It's designed to transfer heat effectively and efficiently. 
Access port on top allows you to start and monitor your engines temperatures 
without having to take the heater off.

XTREME BODY STIFFENERS