New Products
New Products
Home
-
INTELLECT LIPO 1800MAH...
£17.99Intellect RX LiPo Receiver pack.
Ideal for MUGEN MRX and MTC Nitro cars and most others including xray.
1800mAh 2S
13.7*27.5*83mm RX Connector
Only 58g -
Lipo Rx/Tx Flat Pack...
£22.992S Lipo which can be widely used as a receiver (RX) pack and also a transmitter (TX) battery for a wide variety of transmitters including the KO Esprit 4, SANWA Exzes ZZ & Z, MT4-S, M12-RS, M12S and more.
Dimensions 16.8*30.3*85.5mm RX Connector
84.5g 18.24Wh
-
-
Intellect Lipo LiHV...
£37.99For 2019 are Intellect's range of awesome LiPo batteries! The new LiHV HV4 will display a higher voltage and power than 2018 models.
Bench-marked against other leading brands, Intellect batteries provide higher performance for the same specification of battery.
2019 batteries are all Silicon-Graphene based LiHV. Silicon Graphene packs have improved cycle time when charged at 1C rates and can be charged at a higher C rating, with less risk of damage to the pack. LIHV technology has the ability to be charged to 4.35v per cell, but normal racing regulations allow up to 4.2v so LIHV are much safer.
To address market demands 2 options nominally are available Hi Power and Long RunTime.
BRCA/EFRA Legal as of April 2019
Modified and Stock Spec 8 Minute battery
18.5H x 47W x 93L mm
8200mAh
120C
150g
4mm Plugs
Connectors supplied. -
-
CHARGE LEAD XH2S...
£9.992S Lipo charge lead with 4mm charger input plugs and 4-5mm battery plugs, including 2mm balance plug. 600mm. Extremely versatile, suits a wide range of chargers!
-
-
BODY PROTECTION SPONGE...
£2.99RIDE SELF ADHESIVE BODY PROTECTION SPONGE PADS 10PCS
Ideal for protecting your bodies. These foam protectors have an adhesive side for ease of use. Ideal for 1/10th scale and smaller.
-
SKY RC B6ACNEO AC/DC...
£57.99Introducing the new SKY RC B6ACneo AC/DC Charger from SKY RC.
Beauty outside. Beast inside. Performance Punch. Packed with Style.
-
SK-600054-01 - Power...
£10.00SKYRC introduces the POWER SWITCH, a tiny MCU controlled on/off switch for your radio controlled model.
A simple push button operates the switch meaning to eliminate the problems associated with intermittent contact of an ordinary mechanical switch.
The sealed unit is plastic and can easily be mounted to the transponder mount of your model or anywhere else you can mount it using double sided tape.
(Two kinds of bottom covers are included, user can change the bottom cover.)
The switch also features a LiPo mode, by turning this on, the switch unit will auto detect low LiPo voltage and cut off power to protect your LiPo from over dis-charging. This of course can be turned off if you have other safeguards in place or using NiMH/NiCad battery.
Additionally, the power switch informs you about the remaining capacity and conditions of your battery pack. -
SKYRC NITRO ENGINE HEATER
£22.99The SKYRC engine heater uses technology similar to that used by Formula 1, Indy Car and
NASCAR Teams! It will properly pre-heat your engine to 60-70°C in 10 minutes
based on ambient temperature.
SKYRC engine heater will pre-heat all the critical parts of your nitro engine, giving you a
minimal of stress and wear on the engine. It help relieve the stress on the crank,
con-rod, piston and sleeve during warm-up. It also give you a very easy and smooth
engine start, with no stress on your starterbox. Fuel consumption is much less, as
you do not have to spend time warming up and adjusting your engine. A pre-heatet
glow-plug will increase the life of your plug. It is also perfect for break-in, as it
reduces the "pinch" on your new engine. You will experience that engine pre-heating
is a must. Most importantly, it will quickly pay for itself by increasing engine life and
performance!
Features:
MCU control heating time and heating power for maximum safety.
Safety timer: turn off power around 10 minutes automatically.
Built-in temperature sensor: to control the output power of the heater.
LED indicator for status of engine heater.
12V DC source with low voltage cutoff.
Fireproof and heat resistant adjustable cover.
Fits all .19-.26 RC nitro engines.
Very small, lightweight and compact for quick and easy storage.
It's designed to transfer heat effectively and efficiently.
Access port on top allows you to start and monitor your engines temperatures
without having to take the heater off. -
-
-
