SkyRC D260 is a dual channel AC/DC charger, which features an intuitive interface, and its button design makes it incredibly easy to operate. With two independent circuits and the ability to charge batteries up to 6S at maximum 14A per channel, D260 is a smart choice for RC hobbyists.

Specification
Input voltage: AC 100-240V / DC 11-18v
Charge Circuit Power: 130W x 2
Discharge Circuit Power: 10W x 2
Charge Current Range: 0.1-14A x 2
Discharge Current Range: 0.1-2A x 2
Current Drain for Balancing Port:Max 500mA
Trickle Charge Current: NiMH/ NiCd 50-300mA & OFF
DC Power Supply Output: 5-24v /130w x 2
LiPo/LiFe/LiIon/ LiHV Cells: 1-6S
MiMH/ NiCd Cells: 1-15S
Pb Cells: 2-20V
Dimensions: 160x150x71mm
Weight: 896g

Multi-purpose for Most Battery Chemistries
The juice box comes with the charging algorithm for the most common battery chemistries: LiPo, Li-Ion, LiHV, LiFe, NiMH, NiCD, and Pb (lead acid).

Dual Output
D260 allows you to charge two different battery packs simultaneously with 130W rated power per channel. Maximum charge current can be 14 amperes.

Intuitive Operation
The five-button panel and the brightly backlit LCD screen making the charging a breeze even for beginners.
D260 inherits from other chargers by SkyRC; many users will find it very familiar and easy to get started. Even if D260 is your first programmable charger, you’ll find it easy to learn. Users just scroll through parameters, use up/down keys to adjust values, then click a key to enter.

LiHV Mode Available
The additional LiHV mode is able to charge the new generation of LiPo batteries with an end of charge voltage of 4.35V.

Versatile with the Addition of AGM & Cold Modes
AGM (Absorbent Glass Mat) battery is maintenance free, provides excellent electrical reliability, and is lighter than the flooded lead acid type. However, AGM batteries are far more different than normal lead-acid batteries. Although both of them have the same essential components, they have different chemical structures that make them a lot different from each other.Never take the risk of charging AGM batteries with a regular charger in the normal Pb mode.

Smart & Efficient Cooling System
Temperature controlled high speed sleeve bearing cooling fan effectively blows the air through the extruded aluminium heat sink, effectively cooling the device.

DC Power Supply
With just a few clicks, D260 can be turned into a power supply unit to power your hobby equipment. Two channels can be used individually to power two different hobby gadgets simultaneously.

Universal Voltage Input
With the universal-voltage input circuit, you don't need hassle finding a voltage converter between 110V and 220V while traveling around! Even in the field, with the built-in DC input between 11V-18V, racers power the charger with their DIY battery packs.

PC Software for Data Analysis and Firmware Upgrade
Charge Master can start/stop charging process, and view real-time graphs of current, voltage, capacity and monitor single cell voltage.

Supplied with UK 240V plug and 2 x XT60 output leads as shown.

SKYRC introduces the POWER SWITCH, a tiny MCU controlled on/off switch for your radio controlled model.

A simple push button operates the switch meaning to eliminate the problems associated with intermittent contact of an ordinary mechanical switch.
The sealed unit is plastic and can easily be mounted to the transponder mount of your model or anywhere else you can mount it using double sided tape.
(Two kinds of bottom covers are included, user can change the bottom cover.)

The switch also features a LiPo mode, by turning this on, the switch unit will auto detect low LiPo voltage and cut off power to protect your LiPo from over dis-charging. This of course can be turned off if you have other safeguards in place or using NiMH/NiCad battery.
Additionally, the power switch informs you about the remaining capacity and conditions of your battery pack.

The SKYRC engine heater uses technology similar to that used by Formula 1, Indy Car and 
NASCAR Teams! It will properly pre-heat your engine to 60-70°C in 10 minutes 
based on ambient temperature. 

SKYRC engine heater will pre-heat all the critical parts of your nitro engine, giving you a 
minimal of stress and wear on the engine. It help relieve the stress on the crank, 
con-rod, piston and sleeve during warm-up. It also give you a very easy and smooth 
engine start, with no stress on your starterbox. Fuel consumption is much less, as 
you do not have to spend time warming up and adjusting your engine. A pre-heatet 
glow-plug will increase the life of your plug. It is also perfect for break-in, as it 
reduces the "pinch" on your new engine. You will experience that engine pre-heating 
is a must. Most importantly, it will quickly pay for itself by increasing engine life and 
performance! 

Features:

MCU control heating time and heating power for maximum safety. 
Safety timer: turn off power around 10 minutes automatically. 
Built-in temperature sensor: to control the output power of the heater. 
LED indicator for status of engine heater. 
12V DC source with low voltage cutoff. 
Fireproof and heat resistant adjustable cover. 
Fits all .19-.26 RC nitro engines. 
Very small, lightweight and compact for quick and easy storage. 
It's designed to transfer heat effectively and efficiently. 
Access port on top allows you to start and monitor your engines temperatures 
without having to take the heater off.

CAR STAND 1/10 TOURING/1/12TH -BLACK

Sky RC rubber tyre sander can be powered by a 12v power supply as well as directly from a 2s lipo battery. The tyre sander is a quick and easy way to remove the seam from the centre of a new tyre without having to take 2-3 laps around the track.

Features

Rubber tyre sander for touring class

Powerful high torque DC motor with dual metal bearings

Adjustable RPM

8 LED's indicate tyre running RPM

Leightweight aluminium case

Quiet operation

Reverse polarity protection

Tyre rotation can be changed